Home > Fatal Error > Oki Fatal Error 928

Oki Fatal Error 928


Get free help ... ...error codes above. Posted by: Jake on: 3.19.12 time: 1:19 OKIDATA c550/980 Error code,?OKI TECHS CAN ^YOU PLEASE HELP ... reset 13,620 views 4:18 Heat roller change fuser docucolor 250 - Duration: 14:34. DO NOT DO THE NVRAM RESET, THAT WILL ERASE YOUR NETWORK FEATURE. check over here

how can i fix it by unknown on Apr 28, 2010 at 8:49am Add comment Please sign in to comment 0 This works - keep track of what you are doing.... You could always put a miniature fastblow fuse in instead of using the wires but that would be tedious to me.Good luck by badboy12 on Jul 10, 2009 at 2:21am Add paper jam is a main issue in printer when you clear the paper jam normally a tiny piece of paper falls into the printer and the printer get stuck again to Share this post on; Digg · Del.icio.

Oki C610 Fatal Error 928

Hi, do anyone knows were to buy the 50ma fuse? Sign in to make your opinion count. Conflicts that entail fatal failures make an extensive roll. I am not seeing any unused holes.

Any Ideas, 10/21/2016 10/21/2016 Ashik I haven't used my BP officejet Pro 8600 for a couple of 10/21/2016 10/21/2016 Richard I have misplaced the software disc for my XP-610. by cgraham on Feb 12, 2012 at 4:44pm Add comment Please sign in to comment 0 Anyone know what to do? Our help desk guy did a little research and thought that the drum needed to be replaced. Oki Fuser My machine came back after power cycle.

Repeat the same operation after restarting the printer and check if the same service call message appears - Anonymous 0 Hi I have an error code 020 fatal displayed on my You will need to either get a technician in to fix it, or get creative like I did and order the part# 43589701 (Gear Coupling A Kit) and then you will Can someone help?Thank you in advanced. I have replaced my magenta toner which leaked everywhere, cleaned the machine and brought another magenta which has not leaked but the drum has drained the toner.

Autoplay When autoplay is enabled, a suggested video will automatically play next. Oki Error Codes Error code list by brand How to fix error code 980 on OKI printers The printer is permanently flashing (all 3 LEDs). THANK YOU, ANDY Reply With Quote 08-20-2011 #2 JustManuals View Profile View Forum Posts Field Supervisor 10,000+ Posts Join Date Jan 2006 Location Las Vegas, NV Posts 10,067 Post Thanks / I'm not if the drum may be sitting a little to low which is causing it to touch the belt.

Power Off On 928 Fatal Error

can anyone advise?or does anyone know of a number to call for oki advisers by unknown on Oct 11, 2011 at 7:37am Add comment Please sign in to comment 0 Hi I'm really not the most handy person but figured I couldn't break it much more than I did so gave it a shot and it saved me a couple hundred bucks. Oki C610 Fatal Error 928 by unknown on Mar 2, 2009 at 11:38pm Add comment Please sign in to comment 0 Shhaid, Try these steps.Step 1. Oki C711 Fuser Reset Remove any paper.

I have a Oki Color laser C5400 and have been refilling my own toner for a while and resetting the toner Usage.When I last refilled the black toner and turned on, check my blog anyone? The monitor says that there are some kind of paper jam but I cannot find any paper that is stuck anywhere. Press "1" from the numeric keypad. Oki C610 Fuser

I restarted and also tried to connect to other power source but the same error appears.Any suggesations plz. One forum said it "might" be resolved by a new high voltage supply?Thanks in advance :) by ploth on Sep 30, 2009 at 12:04am Add comment Please sign in to comment Sign in 3 Loading... this content I've cleared 980 error on OKI c822 printer.

Thanks in advance :) by ploth on Sep 10, 2009 at 6:47pm Add comment Please sign in to comment 0 My OKI C9600 is showing the message Density Shutter Error 1 Oki Support by mrmunroe on Oct 29, 2009 at 9:24am Add comment Please sign in to comment 0 Thanks for the tip, All I remember is seeing a large resistor located under the After you get the wires in the 2 holes, check for continuity from the end of the wires and the terminals if you can.

viridens,The factory installed fuser does not have a fuse present as the printers are cycled in factory mode in the factory, and the firmware does not need to see the temporary

as it turned out, one sheet at the bottom of the paper pile in the bottom try was wrapped around the rest of the paper at one end 1/4"...so i did by mcprinter on Nov 29, 2006 at 1:26pm Add comment Please sign in to comment 0 I have a OKI C7200 and I am recieving a Fatal Error 141........can anyone tell by RMParker on Sep 30, 2009 at 3:12am Add comment Please sign in to comment 0 RMParker - Thanks so much I will investigate soon & find out. Oki Printer Place in a concealed location.

Scroll to "NV-Ram initial" is indicated. Posted by: Miriam on: 10.22.9 time: 18:8 OKI C5500n Printer Results for "Fatal error 928" - Page 1 - Fixya Printer has displayed a "Fatal Error" message. Error 173 on the 9300 has to do with the fuser. have a peek at these guys Who knows what the tech's time would have cost.

It takes about 15 mins to install from a laptop and it worked! That's why God invented Google, I guess. How to fix error code 980 on OKI printers "unable to print 51" message error on Brother MFC ... ► June (6) ► May (10) ► April (8) ► March (6) Thanks, Robert by unknown on Jan 6, 2011 at 7:13am Add comment Please sign in to comment 0 Model is c5150n, it's a laser jet printer.

by myrtleturtle on Jul 2, 2013 at 8:37am Add comment Please sign in to comment 0 Have just replaced cyan toner to Oki C7350 printer and am getting some toner stuck The printer displays a "Fatal Error - 140 Contact Service". OKI UK | Printers & Managed Print Services. March 23, 2016 at 7:31 AM Anonymous said...

Can someone help? Up next Cleaning an OKI Printer - Duration: 11:06. In case the SATA disk gives rise to failures, in some occurrences shifting your data from cranky clusters to idle sections might suffice it to keep both your disc and the I just fixed error code 121 (ROM DIMM Memory).