Home > Fatal Error > Oki C5900 Fatal Error

Oki C5900 Fatal Error


Check the connection. or its affiliates v The Leading Community for Industry ProfessionalsPrinters Multifunction Large/Wide Format Accessories AV/Presentation Equipment Banking Equipment Binding Equipment Cash Registers Check but of course removing them and putting them onto a new image drum is very messy business.My questions... or it's affiliates. http://brecnc.org/fatal-error/oki-c5900-fatal-error-177.html

by unknown on May 11, 2010 at 5:45am Add comment Please sign in to comment 0 got fatal error 929 hovered the waste toner dry for ages this cleared the error Hi again I posted the above comment and after I went decided to give it one more try and BOOM! Fatal error 980 after a sheet of paper crashed.I installed the 2 wires as mentioned and needed 3 trys ( starting the printer and pulling the wires apart)Third try was succsessful.Thank help by maxandtara on Apr 25, 2012 at 8:29am Add comment Please sign in to comment 0 please oki c5700 message error; power off/on02:error fatal00693894 00694bec 00694bec by unknown on Jun

Oki Fatal Error 980 Reset

I swaped a drum from another cartridge that was working and it still says it's not there. The monitor says that there are some kind of paper jam but I cannot find any paper that is stuck anywhere. Scroll to " Engine Dialog Mode" is indicated.

I'll likely never buy an Okidata printer again. If you don't do this you may access functions that will cause the machine to stop functioning. Do I have any other choices short of replacing this ROM? Oki C711 Fuser Unit I am not seeing any unused holes.

You could always put a miniature fastblow fuse in instead of using the wires but that would be tedious to me.Good luck by badboy12 on Jul 10, 2009 at 2:21am Add Oki C610 Fatal Error 980 Thanks for the post. by unknown on Sep 30, 2009 at 3:05am Add comment Please sign in to comment 0 To Ploth:Service manual says differnt! I have opened the fuser following the steps described but there's definitely no empty slots on my OKI C711 fuser.

The newly designed cartridges by LD seem to either not have the RFID chip in them, or I got a bad one.In any case, I have a toner cartridge that doesn't Oki C711 980 Fatal Error The printer looks for that fuse and if it is not blown it will blow it and reset the life of the fuser to 99%. This ruled out the possibility of a loosened cable or defective board. I got a paper stuck in the fuser and it kind of burned up.

Oki C610 Fatal Error 980

If restarting the printer doesn't solve the problem, replace the fuser. February 11, 2016 at 10:54 PM Anonymous said... Oki Fatal Error 980 Reset You can change this preference below. Κλείσιμο Ναι, θέλω να τη κρατήσω Αναίρεση Κλείσιμο Αυτό το βίντεο δεν είναι διαθέσιμο. Ουρά παρακολούθησηςΟυράΟυρά παρακολούθησηςΟυρά Κατάργηση όλωνΑποσύνδεση Φόρτωση... Ουρά παρακολούθησης Ουρά __count__/__total__ Cleaning Oki Storage Device Manager by unknown on Jul 13, 2009 at 9:06am Add comment Please sign in to comment 0 erro fatal cod:173 okidata c-9300 by joseferreira on Jul 20, 2009 at 7:43am Add comment

One forum said it "might" be resolved by a new high voltage supply? http://brecnc.org/fatal-error/oki-c5900-error-928.html Error 173 on the 9300 has to do with the fuser. Took out to make sure it was seated correctly and put back then 980 again. Actually I've learned they're not fuses, they are thermistors. Oki C610 Fuser

It just keeps saying initializing, can the board be repaired? Reinstall the cartridge and that should get rid of your error.If the problem persists, get in touch with the supplier of your cartridge and arrange for a replacement to be sent Reseat the Toner Cartridges. this content cbale method works fantastic.

Contact conde.com or call 800.826.6332 for information about working with personalized and imaged products created by dye sublimation and heat transfer applications. Oki .pjl File You can't post answers that contain an email address. https://www.dropbox.com/s/p342h3bkirhy1vl/all1.jpg?dl=0 February 26, 2016 at 10:15 PM Marius said...

If you continue we’ll assume you’re OK to receive cookies.

But, it continues to 10/21/2016 10/21/2016 Nathan TO GET MY LAPTOP TO CONNECT TO MY PRINTER AND IT WON'T. 10/20/2016 10/21/2016 Viet - Printer Tech X Ask a Technician Get a Any help would be greatly appreciated. I really wish I had taken pictures along the way, but didn't honestly believe it would work. Oki Fuser Okidata told me to call gilberco which is my company for the passport system that is hooked up to the printer but have not received a reply...because my warranty was over

I want to turn off the sensors but I can't fins anything written that will tell me how to do this. by unknown on Aug 5, 2008 at 2:54am Add comment Please sign in to comment 0 If your getting a 020 fatal error, u need a new TNY prom board, cost Erb says: @keith: I moved on to a Brother MFC-9320CW and have been extremely happy with it. have a peek at these guys by Anonymous on Jul 17, 2008 at 10:19am Add comment Please sign in to comment 0 Quote:"What next?Have OKI c5500Finally fixed paper jam error, then had Fatal Error 928.removed & reinstalled

Any help would be greatly appreciated. Have a manual for Printers & Copiers? Please someone chime in.