Home > Fatal Error > Oki 182 Fatal Error

Oki 182 Fatal Error


Email me for pricing and ordering info. All rights reserved. by unknown on Feb 11, 2013 at 3:07am Add comment Please sign in to comment 0 have you tried contacting OKI Data's customer service? Home OKI Pro & ES Printers Toners & Consumables Accessories Chemical Label Printing Public Sector Graphic Arts Printers Horticultural Label Printing OKI SMART Managed Print Contact Us Sales and support for check over here

Replace the motor. If error is still gone, repeat withg the hard drive. Make sure the wires are long enough to hang out the case. by drhiramortega on Sep 18, 2011 at 10:02am Add comment Please sign in to comment 0 I have a C9600 and it is displaying oki error code 144 - fatal error?

Oki Error Codes

I'd be happy to part with it for a very reasonable sum. Replace it. Sometimes you can just take it out and put it back in and it will work again.

Do I have any other choices short of replacing this ROM? Press the OK button. Note! Oki Fatal Error 980 Reset If the error goes away, power down and install the memory and power up again.

Yes YesPower OFF/ON Replace the spot color PCB Replace the printer control PCB 10: Runaway of the Driver CPU due to noise etc. Oki Fatal Error 928 by mrmunroe on Feb 12, 2012 at 4:56pm Add comment Please sign in to comment 0 I have an okib4600 and i try to print but i get an invalid data....help Replace the LED head unit Replace either applicable PCB. 134-01 to 04: Printer control PCB 134-05: Spot color PCB Service Call 135: Error01: Tray 1 Lift-up Motor Error 02: Tray 2 I also tried to switch to a brothers fax multi func and hook it up to the passport system but it does not pick up any words just marks everything in

One forum said it "might" be resolved by a new high voltage supply? Oki C531dn Error Codes Does this error recur? by unknown on Nov 20, 2008 at 2:25am Add comment Please sign in to comment 0 I have got "Error code 384" and the manual says nothing about it. by unknown on Mar 2, 2009 at 7:14am Add comment Please sign in to comment hello Grolinki may be wrong, but i received the same error, and it turns out my

Oki Fatal Error 928

Yes Power OFF/ON Replace the printer control PCB Power Off/On 250: ErrorSecure File Erasing ErrorAn encrypted file erasing error was detected. Any ideas? Oki Error Codes I was able to reset my Fatal Error 980 code on my C5800. Oki Error 134 YesPower OFF/ON Replace the Printer control PCB Note: Service call errors, 171: Error, 166-02: Error, 168-02: Error, 169-02: Error 0169-04: Error and 902: Error can occur when the printer temperature is

by unknown on Sep 30, 2009 at 3:05am Add comment Please sign in to comment 0 To Ploth:Service manual says differnt! check my blog Do you have a solution for this?Sincerely,Spouine by unknown on Jan 7, 2012 at 2:17am Add comment Please sign in to comment 0 Anyone know what to do? How can I fix this?Thanks by unknown on Sep 5, 2014 at 7:42am Add comment Please sign in to comment 0 my oki machini is showing error 173 fatal what should Zero cost and still using the same fuser unit. Oki Fatal Error Codes

Yes YesPower OFF/ON Replace the tag reader/writer PCB and the FFC. Finally, there was "another" paper jam INSIDE the Fuser. the gear is covered by a spring and cap which connects to the gear on the waste box. this content Here is a list of some of the most common error codes that you may see on your Okidata printer and some helpful tips for fixing the problem: Error Code: 001

by unknown on Nov 8, 2009 at 5:37pm Add comment Please sign in to comment 0 Sometimes all you have to do is take the fuser out and then put it Oki C610 Error Codes by tbjorklund on Sep 12, 2007 at 12:12am Add comment Please sign in to comment Error 005 Program ExceptionThe program has attempted to look up an invalid address Note the 24-digit by unknown on May 13, 2013 at 9:25am Add comment Please sign in to comment 0 Any ideas on how the "Service call - 134:fatal error".

OKI B6500 Led...

Please reply to [emailprotected] for details. - Anonymous It means something it stuck in your fuser unit. If restarting the printer doesn't solve the problem, replace the fuser. Re: RESET OKIDATA TONER DRUM by Anonymous (11/12/07 11:37 AM) reply + / - This took a lot of button gymnastics to figure out, but I hope it is helpful to Oki Troubleshooting as it turned out, one sheet at the bottom of the paper pile in the bottom try was wrapped around the rest of the paper at one end 1/4"...so i did

Prev123456789Next » Not finding what you are looking for? I don't suppose you have a solution to the other thread I posted about my 9850?Thanks againAl by Aln design on Dec 9, 2013 at 3:15pm Add comment Please sign in Remove the rear cover and inspect the initial movement. have a peek at these guys now some of the net guru says it is Magenta image drum problem, but i have reseated all of them 100s of times, it is not go ahead or ending.kinldy anybody

YesPower OFF/ON Replace the Printer control PCB Power Off/On FFF: ErrorCU program error Does this error recur? Yes YesAfter leaving the printer at room temperature, turn on the power again. If you call 1800 807 472 in australia you can get a new one shipped to you but you will have to pay for it - Anonymous 0 service call104: fatal Do I need to replace the toner again or do I have a faulty drum?

Hell, i bought it new for that figured i'd post in case it helps someone else by TheOrig Ralph on Aug 8, 2014 at 11:43am Add comment Please sign in to by Anonymous on Jan 13, 2008 at 4:34am Add comment Please sign in to comment 0 Called Oki for the same error code. YesPower OFF/ON Replace the printer control PCB 03: Runaway of the CPU on the PU due to noise etc. Create your Spare Parts List.

For USB c on ne ct io n, s et [ Op ti on al pa pe r source] manually. Could there be another problem besides the board. The display will now show a binary number with the cursor under the left most digit which is a "0". The drum has 44\% remaining can anyone help?

You need first to check/clean or replace the upper limit switch. Check reproducibility if possible. Reseat the Image Drums. If so then ...

How do you do it ? (FYI :I have reset the drums, and the belt.